KOMPBERG® ZXF90 Oil free Screw Compressor

Refrigeration dryer DRYBERG®️ RF16/AC equals to DRYPOINT®️ RA960/AC Aluminium heat exchanger The heat exchanger module consists of an air/air heat exchanger, an air/refrigerant heat exchanger, and of a high-performance separator. The compressed air flows top-down through the heat exchanger. The large cross-sections of the flow passages cause low flow rates and low compressed-air losses. In the air/air heat exchanger, the heat exchange is effected in a reverse current. This guarantees maximum heat transfer. The heat transfer in the air/refrigerant heat exchanger also takes place in a reverse current. This allows full evaporation of the refrigerant. The high-performance separator ensures almost complete separation of the condensate. Maintenance of the high-performance separator is not required. Technical Data of Refrigeration dryer DRYBERG® RF16/AC equal to DRYPOINT® RA960/AC Refrigeration dryer DRYBERG®️ RF16/AC Volume flow (m3/h) at +3 °C 1008 Power consumption (kW) 1,50 Pressure loss (Δp bar [g]) 0,15 Air connection (ø) G 2 1/2" BSP-F Dimensions AxBxC (mm) 1105x665x725 Weight (kg) 144   Operating pressures multiply air flow with correction factor f1 bar (g) 4 5 6 7 8 10 12 14 f1 0.77 0.86 0.93 1.00 1.05 1.14 1.21 1.27 Ambient air temperatures multiply air flow with correction factor f2 °C 25 30 35 40 45 f2 1.00 0.95 0.88 0.79 0.68 Compressed air inlet temperatures multiply air flow with correction factor f3 °C 25 30 35 40 45 50 55 f3 1.20 1.11 1.00 0.81 0.67 0.55 0.45 Downloads Technical Data DRYBERG®️ RF16/AC Refrigeration dryer, PDF( Size: 450 KB ) Manual DRYBERG®️ RF/AC, PDF( Size: 5 MB )  

Compressed air filter PUREBERG® F20(Type)W ,1176 Nm3/h at 7 bar General filter, Fine filter, Superfine filter, Activated carbon filter Innovative features mean outstanding performance without compromise  Compressed air filter PURBERG® housings have been developed for high-efficiency removal of solid particles, water, oil aerosols, hydrocarbons, odour vapours from com­pressed air systems. To meet the required com­pressed air quality appropriate filter element (G, F, S, A) must be installed into the filter housing. Housing prevents condensate from being picked up and "car­ried over" into the airstream. The BERG compressed air filter technolo­gy guarantees low operating costs, long service life, outstanding process reliability, and safe filtration.    Technical Data of Compressed air filter  Compressed air filter PUREBERG® F20(Type)W Operating pressure [bar] 0 - 20 Pipe Size [inch] 2 Flow Capacity [m3/h] 1176 Flow Capacity [Scfm] 692 Dimensions (AxBxCxD) [mm] 605 x 160 x 43 x 180 Volume [l] 6,0 Weight [kg] 5,1 Operating temperature [°C] 1,5 - 65 Housing material Aluminium Cover ABS Sealing NBR Corrosion protection Anodized (optional) Outside protection Powder paint coated (Epoxy-polyester base)       G General Filter F Fine Filter S Superfine Filter A Activated carbon Quality class - particle (ISO8573-1) 3 2 1 1 Residual oil content (mg/m3) <1 <0.1 <0.01 <0.005 Quality class - Oil (ISO8573-1) 3 2 1 0 Pressure drop - new element (mbar) 20 50 60 60 change filter cartridge at pressure drop (mbar) 350 350 350 6 months Filter media Acrylic fibers Borosilicate microfibers Activate carbon   Operating pressure - Correction factors  Operating pressure (bar) 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Correction factors  0.63 0.75 0.88 1.00 1.13 1.25 1.38 1.50 1.63 1.75 1.88 2.00 2.13 2.25 2.38 2.50 2.63 Downloads Compressed air filter Installation And Operating Manual , PDF ( Size: 1 MB )

Optimize Operations: PUREBERG F24WW Water Separator Solution A water separator, also called a condensate separator, is a device that removes moisture and water from an air flow. In the area of air compressors and compressed air systems, the water separator is important to ensure that the air remains dry. Moisture in the compressed air can otherwise lead to problems such as rust, blocked lines and damage to machines. The water separator PUREBERG® F24WW, (1440 m3/h at 7 bar) is a widely used example in the industry. The water separator works through various mechanisms to separate the condensate from the air. In most cases it uses centrifugal force or gravity to remove the water from the airflow. As the moist air flows through the separator, the water droplets are pulled out of the air by these forces and collect at the bottom of the separator. From there, the accumulated water can be removed from the system either manually or automatically. There are different types of water separators, including condensate separators for air compressors, compressed air lines or industrial applications. Choosing the right water separator for the device depends on various factors. These include: flow rate, pressure, ambient temperature and the specific requirements of the program. In summary, the water separator is very important in compressed air systems. It helps make the air cleaner, improve operations and make machines last longer. How often should water separators PUREBERG FWW be cleaned? The frequency of cleaning water separators like the PUREBERG FWW will depend on several factors, including the operating conditions of your compressed air system, the level of contaminants in the air, and the manufacturer's recommendations. However, as a general guideline, it is typically recommended to clean water separators at least once every 3 to 6 months. Regular cleaning of water separators is essential to ensure their optimal performance and efficiency in removing moisture and contaminants from the compressed air. Accumulated dirt, debris, and moisture can impair the functionality of the separator, leading to reduced air quality, increased energy consumption, and potential damage to downstream equipment.  When cleaning a water separator like the PUREBERG FWW, follow these steps: Shut down the compressed air system: Before starting the cleaning process, make sure to shut down the compressed air system and depressurize the lines to prevent any accidents or injuries. Remove the water separator: Carefully disconnect the water separator from the compressed air system according to the manufacturer's instructions. This may involve loosening fittings, disconnecting hoses, or removing mounting brackets. Inspect and clean the separator: Inspect the interior of the water separator for any dirt, debris, or moisture buildup. Use a soft brush, cloth, or compressed air to remove any contaminants from the separator's components, such as the filter element or drain valve. Check for damage: While cleaning the water separator, inspect it for any signs of damage, such as cracks, leaks, or corrosion. Replace any damaged parts to ensure the separator functions properly. Reassemble and reinstall: Once the water separator is clean and free of debris, reassemble it according to the manufacturer's instructions. Reinstall the separator back into the compressed air system and secure it in place. Test the system: After cleaning and reinstallation, test the compressed air system to ensure that the water separator is functioning correctly and effectively removing moisture from the air. By following these steps and cleaning your water separators like the PUREBERG FWW on a regular basis, you can maintain the efficiency and performance of your compressed air system and prolong the lifespan of the equipment. Technical data of water separator Water separator PUREBERG® F24WW Operating pressure [bar] 0 - 20 Pipe Size [inch] 2 1/2 Flow Capacity [m3/h] 1440 Flow Capacity [Scfm] 847 Dimensions (AxBxCxD) [mm] 685 x 160 x 43 x 200 Volume [l] 6,5 Weight [kg] 6,3 Operating temperature [°C] 1,5 - 65 Housing material Aluminum Cover ABS Sealing NBR Corrosion protection Stainless Steel 1.4301 Outside protection Anodized (optional) Included BEKOMAT 20   Operating pressure - Correction factors  Operating pressure (bar) 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Correction factors  0.63 0.75 0.88 1.00 1.13 1.25 1.38 1.50 1.63 1.75 1.88 2.00 2.13 2.25 2.38 2.50 2.63 Downloads Water separator Installation And Operating Manual , PDF ( Size: 490 KB )

BEKO condensate drain BEKOMAT® 20BEKOMAT® 20 | 20FM for Filters and water separators The BEKOMAT 20 is a strong condensate drain designed for use in water separators and air filters. It is suitable for oil-lubricated plants as well as oil-free compressors. The control panel is accessible from the top and the front. It has a plastic housing with integrated aluminum condensate container. The BEKOMAT 20 FM with integrated filter management is a cost effective monitoring solution for the service filters element. Technical data of BEKOMAT® 20 BEKOMAT® BEKOMAT® 20 Max. compressor performance [m³/min] 4 Max. dryer performance [m³/min] 8 Max. filter performance [m3/min] 40 Voltage 230VAC / 50-60Hz Operating pressure [bar] 0,8 - 16 Temperature [°C] +1 to + 60 Condensate feed 1 x G 1/2 , 1 x G 3/4 Condensate drain DN 8-10 bzw. G 1/4i Dimensions B x T x H [mm] 140 x 72 x 140 Weight [kg] ca. 0,7 Here are some advantages and uses of the BEKOMAT 20: Efficient condensate drainage: The BEKOMAT 20 is designed to effectively remove condensate from compressed air systems, ensuring optimal performance and preventing damage to downstream equipment. Energy-saving: The unit operates based on demand, meaning it only activates when condensate needs to be drained, helping to reduce energy consumption. Easy maintenance: The BEKOMAT 20 is designed for easy installation and maintenance, making it user-friendly for operators. Reliable operation: Beko Technologies is known for producing high-quality products, and the BEKOMAT 20 is no exception, offering reliable performance in industrial applications.  BEKOMAT 20 Applications:Industrial compressed air systems: The BEKOMAT 20 is commonly used in industrial settings where compressed air is a critical component of operations, such as manufacturing plants, automotive facilities, and food processing plants. Air compressors: The unit can be installed in conjunction with air compressors to ensure efficient condensate removal and protect the integrity of the compressed air system. Pneumatic tools and equipment: The BEKOMAT 20 can help maintain the performance and longevity of pneumatic tools and equipment by preventing moisture buildup in the air supply. Overall, the BEKOMAT 20 is a reliable and efficient condensate drain unit that offers several advantages in maintaining the performance of compressed air systems.  Downloads Technical Data BEKOMAT® 20, PDF (Size: 2.5 MB) BEKOMAT® 20 datasheets, PDF ( Size: 330 KB )