BEKOMAT® , ÖWAMAT®, QWIk-PURE®

BEKO condensate drain BEKOMAT® - BEKO Technologies

At almost all stations in the compressed air treatment process, condensate is generated. It is mostly oily, contaminated with dirt particles and spreads throughout the compressed air network. We help you to remove condensate from the compressed air and to achieve the optimum quality for your application: with the BEKOMAT®. The first electronically level-controlled steam trap has become synonymous with condensate drainage. Quantity-adjusted and with intelligent electronics against compressed air losses it minimizes energy expenditure and costs. This also confirms the practice: well-known compressor manufacturers worldwide rely on the BEKOMAT® when it comes to safe and economical condensate drainage. The zero loss Air condansate drain, BEKOMAT® is truly made in Germany by BEKO technologies GmbH. 

Safe and efficient oil-water separation: ÖWAMAT®

The ÖWAMAT® is an oil-water separation system for dispersed condensates that has been tried and tested for decades. It has a building authority approval for the versions with and without free oil separation, for synthetic and mineral oils as well as for the treatment of condensate from reciprocating compressors, and therefore does not require a permit under water law. 

As the first active oil-water separator,the QWIK-PURE ® opens up new possibilities.

Classic oil-water separators based on the principle of gravity separation can hardly be improved in terms of process technology. So, as condensate technology experts with decades of experience, we have paid special attention to the people who work with the product. What is important to them, what drives them and how can we give them the highest degree of decision-making reliability and flexibility while integrating the requirements of modern industry? As a result, we present the QWIK-PURE ®, the first active oil-water separator with which we have fundamentally redefined condensate treatment and will change it worldwide.
%
BEKOMAT® 20, BEKO condensate drain
BEKO condensate drain BEKOMAT® 20 how can you prevent condensate damage to your compressed air system whilst saving energy and adapted to the amount of condensate without loss of compressed air These are the proven strength of a BEKOMAT® but exactly how does it work Adapted to the amount of condensate and without compressed air loss Condensate flows in via the feed line whilst air pressure from the vent pipe keeps the membrane closed from above a capacitive sensor constantly monitors the condensate. When the condensate reaches a preset level the control unit immediately initiates the draining of the condensate. Once again as the condensate flows in the membrane remains closed due to system pressure it's larger upper surface provides the necessary closing force on the valve seat and seals it tightly when the BEKOMAT is full the solenoid valve is activated and the space above the membrane is vented. Simultaneously the pressure on the underside increases allowing the condensate to flow into the outlet line. in actual operation the solenoid valve switches so quickly that no valuable compressed air escapes. The BEKOMAT® drains the condensate into the OWAMAT® Oil water separator mounted downstream adapted to the amount of condensate and without compressed air loss.   BEKOMAT® 20 | 20FM for Filters and water separators The BEKOMAT® 20 is a sturdy condensate drain designed for use in water separators, filters and similar equipment. It is suitable for oil-lubricated plants as well as oil-free compressors. The control panel is accessible from the top and the front. It has a plastic housing with integrated aluminium condensate container. The BEKOMAT 20 FM with integrated filter management (filter service life monitor and indicator) is a cost effective monitoring solution for the connected filter element.   Technical data of BEKOMAT® 20 BEKOMAT® BEKOMAT® 20 Max. compressor performance [m³/min] 4 Max. dryer performance [m³/min] 8 Max. filter performance [m3/min] 40 Voltage 230VAC / 50-60Hz Operating pressure [bar] 0,8 - 16 Temperature [°C] +1 to + 60 Condensate feed 1 x G 1/2 , 1 x G 3/4 Condensate drain DN 8-10 bzw. G 1/4i Dimensions B x T x H [mm] 140 x 72 x 140 Weight [kg] ca. 0,7 Downloads Technical Data BEKOMAT® 20, PDF (Size: 2.5 MB) BEKOMAT® 20 datasheets, PDF ( Size: 330 KB )

Net €161.00 €191.59* €273.70* (30% saved)
%
BEKOMAT® 20 FM, BEKO condensate drain
BEKO condensate drain BEKOMAT® 20 FMBEKOMAT® 20 | 20FM for Filters and water separators The BEKOMAT® 20 FM with integrated filter management (filter status time display and filter status control) is a cost-effective monitoring solution for the connected filter element. It is designed as a robust condensate drain for water separators, filters or similar applications and can be used both in systems with oil-lubricated as well as with oil-free compressors. The plastic housing of the BEKOMAT 20 FM is equipped with an internal aluminium condensate container. The front panel is visible and can be operated from the top and the front.   Technical data of BEKOMAT® 20 FM BEKOMAT® BEKOMAT® 20FM Max. compressor performance [m³/min] 4 Max. dryer performance [m³/min] 8 Max. filter performance [m3/min] 40 Voltage 230VAC / 50-60Hz Operating pressure [bar] 0,8 - 16 Temperature [°C] +1 bis + 60 Condensate feed 1 x G 1/2 , 1 x G 3/4 Condensate drain DN 8-10 bzw. G 1/4i Dimensions B x T x H [mm] 140 x 72 x 140 Weight [kg] ca. 0,7 Downloads Technical Data BEKOMAT® 20 FM , PDF( Size: 103 MB )BEKOMAT® 20 FM data sheets , PDF( Size: 330 KB )

Net €209.30 €249.07* €355.81* (30% saved)
%
BEKOMAT® 31U, BEKO condensate drain
BEKO condensate drain BEKOMAT® 31U BEKOMAT® with service concept – quick and economic The innovative design of the BEKOMAT® 31U, 32U, 33U and 33U CO series enables simplified handling as well as installation and maintenance with minimum time expenditure. The devices consist of no more than three units joined together with quick-release connectors. The control and sensor units are only installed once, only the service unit (including all wear and pressure parts) needs to be exchanged for maintenance purposes. This robust condensate drain is suitable for both oil-contaminated and oil-free, aggressive condensates.   Technical data of BEKOMAT® 31U BEKOMAT® BEKOMAT® 31U Max. compressor performance [m³/min] 2,5 Max. dryer performance [m³/min] 5 Max. filter performance [m3/min] 25 Voltage 230VAC / 50-60Hz Operating pressure [bar] 0.8 - 16 Temperature [°C] +1 bis + 60 Condensate feed 1 x G 1/2  Condensate drain DN 8-10 bzw. G 1/4i Dimenstions B x T x H [mm] 65 x 164 x 118 Weight [kg] ca. 0,8 Downloads Technical Data BEKOMAT 31U , PDF( Size: 189 KB ) Catalog BEKOMAT 31U , PDF( Size: 368 KB )

Net €138.60 €164.93* €235.62* (30% saved)
%
BEKOMAT® 32U, BEKO condensate drain
BEKO condensate drain BEKOMAT® 32U Comfortable and simplified maintenance A service indicator informs punctually about the upcoming maintenance and/or exchange for the service unit. All parts which are subject to wear or are pressurised can be reached with one manual movement. Neither electrical installations nor the installation of seals and individual parts are necessary. The installation concept is also particularly user-friendly and time-saving: The device only has to be connected once electrically. The robust housing is also waterproof according to IP67. BEKOMAT® 31U | 32U facilitates the connection to the compressed air system with an angle adaptor. If the service unit of the BEKOMAT® 33U is disconnected from the power supply and condensate receiver tank, then the supply tank always remains connected to the compressed air system. This saves time and effort during maintenance.   Technical data of BEKOMAT® 32U BEKOMAT® BEKOMAT® 32U Max. compressor performance [m³/min] 5 Max. dryer performance [m³/min] 10 Max. filter performance [m3/min] 50 Voltage 230VAC / 50-60Hz Operating pressure [bar] 0.8 - 16 Temperature [°C] +1 bis + 60 Condensate feed 1 x G 1/2  Condensate drain DN 8-10 bzw. G 1/4i Dimenstions B x T x H [mm] 74 x 179 x 130 Weight [kg] ca. 1,0 Proper use • The BEKOMAT® 32U is an electronically level-controlled condensate drain for compressed-air plants. • The device is employed within the permissible performance parameters (see "Technical data"). • The BEKOMAT® 32U is able to drain condensate under operating pressure from the plant components virtually without compressed-air loss. • For its function, the BEKOMAT® 32U requires a supply voltage and an operating pressure (see "Technical data"). • As far as the employment in plants with increased demands on compressed air is concerned (food industry, medical technology, laboratory equipment, special processes etc.), the operator must decide on measures for the monitoring of the compressed-air quality. These have an effect on the safety of the subsequent processes and may prevent damage to persons and plants. • It is the task of the operator to ensure that the indicated conditions are met during the entire operating time. Exclusion from the scope of application • The BEKOMAT® 32U as a condensate drain alone cannot guarantee a defined compressed-air quality, for this purpose, other additional technical devices are required. • BEKOMAT® 32U is not suitable for use in plants carrying vacuum or atmospheric ambient pressure or in ex-areas. • The BEKOMAT® 32U must not be exposed to permanent direct solar or thermal radiation. • The BEKOMAT® 32U must not be installed and operated in areas with an aggressive atmosphere. • The BEKOMAT® 32U is not heatable and, therefore, not suitable for the use in areas where frost is likely to occur. • The BEKOMAT® 32U is not suitable for CO2 plants. Downloads Technical Data BEKOMAT® 32U PDF( Size: 186 KB ) Catalog BEKOMAT® 32U , PDF( Size: 368 KB )

Net €208.25 €247.82* €291.55* (15% saved)
BEKOMAT® 33U, BEKO condensate drain
BEKO condensate drain BEKOMAT® 33U Comfortable and simplified maintenance A service indicator informs punctually about the upcoming maintenance and/or exchange for the service unit. All parts which are subject to wear or are pressurised can be reached with one manual movement. Neither electrical installations nor the installation of seals and individual parts are necessary. The installation concept is also particularly user-friendly and time-saving: The device only has to be connected once electrically. The robust housing is also waterproof according to IP67. BEKOMAT® 31U | 32U facilitates the connection to the compressed air system with an angle adaptor. If the service unit of the BEKOMAT® 33U is disconnected from the power supply and condensate receiver tank, then the supply tank always remains connected to the compressed air system. This saves time and effort during maintenance.   Technical data of BEKOMAT® 33U BEKOMAT® BEKOMAT® 33U Max. compressor performance [m³/min] 10 Max. dryer performance [m³/min] 20 Max. filter performance [m3/min] 100 Voltage 230VAC / 50-60Hz Operating pressure [bar] 0.8 - 16 Temperature [°C] +1 to + 60 Condensate feed 3 x G 1/2  Condensate drain DN 13 bzw. G 1/2i Dimensions B x T x H [mm] 73 x 203 x 157 Weight [kg] ca. 1,7 Downloads Technical Data BEKOMAT 33U, Instructions for installation and operation, PDF( Size: 1 MB ) Catalog BEKOMAT 33U , PDF( Size: 368 KB )

From Net €359.55 €427.86*
%
BEKOMAT® 12, 12CO, 12CO PN 63, BEKO condensate drain
BEKO condensate drain BEKOMAT® 12, 12CO, 12CO PN63Cost-effective and reliable: BEKOMAT® standard units The BEKOMAT® range provides the 12, 13, 14 and BEKOMAT® 16 standard units for virtually every application, which are not just the correct solution, rather more also the most suitable low-energy solution. The integrated capacitive sensor for volume-controlled condensate discharge helps save energy and enhances efficiency – which is what you would expect from BEKOMAT.   Technical Data BEKOMAT® 12, 12CO, 12CO PN63 BEKOMAT® 12 12 CO 12 CO PN63 Max. compressor capacity 8 m3/min Max. refrigeration dryer performance 16 m3/min Max. filter performance 80 m3/min Min./max. operating pressure 0,8 ... 16 bar (g) 1,2 ... 63 bar (g) Housing Aluminium Aluminium, hard-coated Ambient temperature +1 °C … +60 °C Weight (empty) 0,8 kg 0,9 kg Condensate inlet 1 x G½ (inside) [optional: NPT thread] Condensate discharge 1 x G⅜ (outside); hose connector, hose Ø = 10-13 mm (inside) Operating voltage 230 / 200 / 115 / 100 / 24 VAC ± 10%, 50 ... 60 Hz / 24 VDC ± 10% Power consumption P < 8,0 VA (W) Protection class IP 65 Wire cross-section (mains connection) recommended 3 x 0.75 … 1.5 mm2 (AWG 16 ... 18) Protection recommended for AC: 1 A slow / mandatory for DC: 1 A slow Contact load max. AC 250 V, DC 30 V / 1A; min. DC 5V / 10 mA Condensate oil-contaminated condensate oil-contaminated condensate; oil-free, potentially aggressive condensate Downloads Technical Data BEKOMAT® 12, 12CO, 12CO PN63 , PDF( Size: 94 KB ) Catalog BEKOMAT® 12, 12CO, 12CO PN63, PDF( Size: 430 KB )

Net €330.00 €392.70* €462.91* (15.17% saved)
%
Top
BEKOMAT® 13, 13CO, 13 CO PN 50 , BEKO condensate drain
BEKO condensate drain BEKOMAT® 13, 13CO, 13 CO PN 50 how can you prevent condensate damage to your compressed air system whilst saving energy and adapted to the amount of condensate without loss of compressed air These are the proven strength of a bekomat but exactly how does it work Adapted to the amount of condensate and without compressed air loss Condensate flows in via the feed line whilst air pressure from the vent pipe keeps the membrane closed from above a capacitive sensor constantly monitors the condensate. When the condensate reaches a preset level the control unit immediately initiates the draining of the condensate. Once again as the condensate flows in the membrane remains closed due to system pressure it's larger upper surface provides the necessary closing force on the valve seat and seals it tightly when the bekomat is full the solenoid valve is activated and the space above the membrane is vented. Simultaneously the pressure on the underside increases allowing the condensate to flow into the outlet line. in actual operation the solenoid valve switches so quickly that no valuable compressed air escapes. The bekomat® drains the condensate into the owamat Oil water separator mounted downstream adapted to the amount of condensate and without compressed air loss.   Cost-effective and reliable: BEKOMAT® standard units The standard design is made in corrosion-resistant aluminium, which makes the BEKOMAT® particularly reliable and robust. A silver-coloured coating protects the outside of the housing. The BEKOMAT® CO models are predestined for operating with oil-free or aggressive condensates. Their housing is additionally, completely glass bead blasted and protected by a high-quality hard coating.   Technical Data BEKOMAT® 13, 13CO, 13CO PN50 BEKOMAT® 13 13 CO 13 CO PN50 Max. compressor capacity 35 m3/min Max. refrigeration dryer performance 70 m3/min Max. filter performance 350 m3/min Min./max. operating pressure 0,8 ... 16 bar (g) 1.2 ... 25 or 40 bar or 50 bar (gauge) Housing Aluminium Aluminium, hard-coated Ambient temperature +1 °C … +60 °C Weight (empty) 2 kg 2,2 kg Condensate inlet 2 x G½ (inside) [optional: NPT thread] Condensate discharge 1 x G½ (outside); hose connector, hose Ø = 13 mm (inside) 1 x G⅜ (inside); hose connector, hose Ø = 13 mm (inside) Operating voltage 230 / 200 / 115 / 100 / 24 VAC ± 10%, 50 ... 60 Hz / 24 VDC ± 10% Power consumption P < 8,0 VA (W) Protection class IP 65 Wire cross-section (mains connection) recommended 3 x 0.75 … 1.5 mm2 (AWG 16 ... 18) Protection recommended for AC: 1 A slow / mandatory for DC: 1 A slow Contact load max. AC 250 V, DC 30 V / 1A; min. DC 5V / 10 mA Condensate oil-contaminated condensate oil-contaminated condensate; oil-free, potentially aggressive condensate Measures: • Do not exceed the maximum operating pressure (see type plate)! • Only carry out service measures when the system is pressure less. • Use pressure-resistant installation material only. • The feed pipe must be tubed firmly. Discharge pipe: short, fixed pressure hose onto pressure-resistant pipe. • Make sure that persons or objects cannot be hit by condensate or escaping compressed air. Downloads Technical Data BEKOMAT® 13, 13CO, 13 CO PN 50 , PDF( Size: 1.5 MB ) Catalog BEKOMAT® 13, 13CO, 13 CO PN 50 , PDF( Size: 430 KB )

Net €470.00 €559.30* €658.07* (15.01% saved)
%
BEKOMAT® 14, 14CO, 14CO PN25, BEKO condensate drain
BEKO condensate drain BEKOMAT® 14, 14CO, 14CO PN25 Cost-effective and reliable: BEKOMAT ® standard units The BEKOMAT® range provides the 12, 13, 14 and BEKOMAT 16 standard units for virtually every application, which are not just the correct solution, rather more also the most suitable low-energy solution. The integrated capacitive sensor for volume-controlled condensate discharge helps save energy and enhances efficiency – which is what you would expect from BEKOMAT. Unnecessary costs and damage in the compressed air generation can only be efficiently prevented with volume-controlled condensate discharge. For this reason, BEKOMAT condensate drain therefore functions with a capacitive sensor. The intelligent electronics prevent compressed air losses and minimise energy consumption. Due to this the electronically regulated condensate discharge, the drain often amortises itself within half a year compared to devices with time-controlled drain valves.   Technical Data BEKOMAT® 14, 14CO, 14CO PN25 BEKOMAT® 14 14 CO 14 CO PN25 Max. compressor capacity 150 m3/min Max. refrigeration dryer performance 300 m3/min Max. filter performance 1500 m3/min Min./max. operating pressure 0,8 ... 16 bar (g) 1.2 ... 25 bar (gauge) Housing Aluminium Aluminium, hard-coated Ambient temperature +1 °C … +60 °C Weight (empty) 2.9 kg 3.1 kg Condensate inlet 3 x G¾ (inside) [optional: NPT thread] Condensate discharge 1 x G½ (outside); hose connector, hose Ø = 13 mm (inside) 1 x G⅜ (inside); hose connector, hose Ø = 13 mm (inside) Operating voltage 230 / 200 / 115 / 100 / 24 VAC ± 10%, 50 ... 60 Hz / 24 VDC ± 10% Power consumption P < 8,0 VA (W) Protection class IP 65 Wire cross-section (mains connection) recommended 3 x 0.75 … 1.5 mm2 (AWG 16 ... 18) Protection recommended for AC: 1 A slow / mandatory for DC: 1 A slow Contact load max. AC 250 V, DC 30 V / 1A; min. DC 5V / 10 mA Condensate oil-contaminated condensate oil-contaminated condensate; oil-free, potentially aggressive condensate Proper use • The BEKOMAT® is an electronically level-controlled condensate drain for compressed-air plants. • It is employed within the permissible operating parameters (see "Technical data"). • The BEKOMAT® is able to drain condensate under operating pressure from the plant components virtually without compressed-air losses. • For its function, the BEKOMAT® 14 requires an operating voltage and an operating pressure (see "Technical data"). • As far as the employment in plants with increased demands on the compressed-air quality is concerned (food industry, medical technology, laboratory equipment, special processes etc.), the operator must decide on measures for the monitoring of the compressed-air quality. These have an effect on the safety of the subsequent processes and may prevent damage to persons and plants. • It is the task of the operator to ensure that the indicated conditions are met during the entire operating time. • For the employment in CO2 plants, a BEKOMAT® with a CO specification (BEKOMAT® ... CO) must be used. • The BEKOMAT® and the condensate supply line need to be protected against frost, as otherwise the function cannot be guaranteed. BEKO TECHNOLOGIES GMBH also offers suitable products for this purpose. Downloads Technical Data BEKOMAT® 14, 14CO, 14CO PN25 , PDF( Size: 1.5 MB ) Catalog BEKOMAT® 14, 14CO, 14CO PN25 , PDF( Size: 430 KB )

Net €623.90 €742.44* €873.46* (15% saved)
BEKOMAT® 16 CO, BEKO condensate drain
Condensate drainage without loss of compressed air If a float arrester leaks, high costs arise as a result of leaks. Time-controlled solenoid valves also cause compressed air losses. During the valve opening expensive compressed air escapes unused into the environment. In contrast, a condensate drain with electronic level control guarantees draining without compressed air, ie energy loss. This not only saves energy and costs, but also CO 2 emissions.This is a fantastic condansate drainage without loss of compressed air.    Technical data of BEKOMAT® 16 CO BEKOMAT® BEKOMAT® 16 CO Max. compressor performance [m³/min] 1400 Max. dryer performance [m³/min] 2800 Max. filter performance [m3/min]   Voltage 230VAC / 50-60Hz Operating pressure [bar] 0.8 - 16 Temperature [°C] +1 bis + 60 Condensate feed 2 x G 3/4 | 1 x G 1 Condensate drain DN 10-13 bzw. G 1/2i Dimenstions B x T x H [mm] 260 x 280 x 280 Weight [kg] ca. 6,1 Further safety advice: • For installation and operation, the national regulations and safety codes in force must also be adhered to. • Do not use the BEKOMAT® 16 in hazardous areas. • Regarding the inlet screw joints, excessive tightening forces must be avoided. This applies in particular to conical screw joints. • The BEKOMAT® 16 will only function when voltage is applied. • Do not use the test button for permanent drainage! • Only use genuine spare parts! This is imperative to ensure perfect functioning. Function Of BEKOMAT® 16 CO The condensate flows through the feed line (1) into the BEKOMAT® unit and accumulates in the container (2). A capacitive sensor (3) continuously registers the liquid level and passes a signal to the electronic control as soon as the container is filled. The pilot valve (4) is then activated and the diaphragm (5) opens the outlet line (6) for discharging the condensate. When the BEKOMAT® unit has been emptied, the outlet line is closed again quickly and tightly without wasting compressed air. 1- Ready for operation Voltage is being applied 2- Discharge procedure Outlet line is open 3- Malfunction Alarm mode is activated 4- Test Manual drainage / alarm When the microcontroller registers a malfunction, the device will automatically change to the alarm mode. The switching sequence of the valve (see illustration) continues until the fault is cleared (automatically or through maintenance). The red LED flashes as long as the device is in the alarm mode. Malfunctioning could be caused by, e.g.: • Mistakes during installation • Dropping below the necessary minimum pressure • Excessive condensate quantities (overloading) • Blocked / shut off outlet line • Extreme amount of dirt particles • Frozen piping If the fault is not cleared within the first minute, a fault signal is triggered (see illustration) which can be picked off as a potential-free signal via the alarm relay. Downloads Technical Data BEKOMAT® 16 CO , PDF( Size: 1.2 MB ) Catalog BEKOMAT® 16 CO , PDF( Size: 430 KB )

Net €1,627.00 €1,936.13*
BEKOMAT® 3 CO EX BEKO condensate drain
BEKO condensate drain BEKOMAT® 3 CO EX Condensate drainage without loss of compressed air If a float arrester leaks, high costs arise as a result of leaks. Time-controlled solenoid valves also cause compressed air losses. During the valve opening expensive compressed air escapes unused into the environment. In contrast, a condensate drain with electronic level control guarantees draining without compressed air, ie energy loss. This not only saves energy and costs, but also CO 2 emissions. This is a fantastic condensate drainage without loss of compressed air.    Technical data of BEKOMAT® 3 CO EX BEKOMAT® BEKOMAT® 3 CO EX Compressor Capacity [m³/min] 100 Voltage 12 VDC Operating pressure [bar] 0.8 - 16 Temperature [°C] +1 to + 60 Condensate feed 3 x G 3/4  Dimensions B x T x H [mm] 160 x 193 x 255 Weight [kg] ca. 5,0 Application Oil-contaminated condensate | oil-free, often aggressive condensate   Function Of BEKOMAT® 3 CO EX Empty state: Condensate drips through the inlet opening 1- and collects in the container 2- The diaphragm valve 5- is closed because the pressure equalization across the valve diaphragm via the pilot line 3- and the solenoid valve 4- 5- takes place. The larger area above the membrane causes a high closing force. The valve seat remains closed without leaks. Filled state: If the container 2- is filled with condensate so that the capacitive level sensor 6- reports a signal at the maximum point, the solenoid valve is switched and the area above the valve membrane is vented. The valve membrane lifts off the valve seat 7-, the overpressure in the housing pushes the condensate into the outlet line 8- The valve is closed leak-free before the compressed air escapes. If the condensate drain is disturbed (blocked drain line, defective membrane), the alarm mode is triggered after 60 seconds. The LED flashes, a fault message can be picked up as a potential-free signal via the alarm relay. With Ex devices this is possible via a built-in optocoupler and a switching amplifier. In this state, the solenoid valve is opened for 7.5 seconds every 4 minutes. A BEKOMAT® filled in a pressure less state is automatically alarm-free again under pressure. The drained condensate is now sent to the ÖWAMAT® oil-water separator for disperse condensate for treatment. In the case of stable emulsions, we recommend the BEKOSPLIT® splitting system for almost waste-free processing. Both systems offer legally compliant process technology for treating your compressed air condensate. Downloads Technical Data BEKOMAT® 3 CO EX , PDF( Size: 702 KB ) Data sheet BEKOMAT® 3 CO EX , PDF( Size: 154 KB ) Technical Data sheet of BEKOMAT® 3 CO EX , PDF( Size: 63 KB ) Catalog BEKOMAT® 3 CO EX , PDF( Size: 509 KB )

Net €1,599.00 €1,902.81*
BEKOMAT® 6 CO EX BEKO condensate drain
BEKO condensate drain BEKOMAT® 6 CO EX Condensate drainage without loss of compressed air If a float arrester leaks, high costs arise as a result of leaks. Time-controlled solenoid valves also cause compressed air losses. During the valve opening expensive compressed air escapes unused into the environment. In contrast, a condensate drain with electronic level control guarantees draining without compressed air, ie energy loss. This not only saves energy and costs, but also CO 2 emissions.This is a fantastic condansate drainage without loss of compressed air.    Technical data of BEKOMAT® 6 CO EX BEKOMAT® BEKOMAT® 6 CO EX Compressor Capacity [m³/min] 1000 Voltage 12 VDC Operating pressure [bar] 0.8 - 16 Temperature [°C] +1 bis + 60 Condensate feed 2 x G¾ | 1x G1 Dimenstions B x T x H [mm] 260 x 280 x 295 Weight [kg] ca. 5,0 Application Oil-contaminated condensate | oil-free, often aggressive condensate   Function Of BEKOMAT® 6 CO EX Empty state: Condensate drips through the inlet opening 1- and collects in the container 2- The diaphragm valve 5- is closed because the pressure equalization across the valve diaphragm via the pilot line 3- and the solenoid valve 4- 5- takes place. The larger area above the membrane causes a high closing force. The valve seat remains closed without leaks. Filled state: If the container 2- is filled with condensate so that the capacitive level sensor 6- reports a signal at the maximum point, the solenoid valve is switched and the area above the valve membrane is vented. The valve membrane lifts off the valve seat 7-, the overpressure in the housing pushes the condensate into the outlet line 8- The valve is closed leak-free before the compressed air escapes. If the condensate drain is disturbed (blocked drain line, defective membrane), the alarm mode is triggered after 60 seconds. The LED flashes, a fault message can be picked up as a potential-free signal via the alarm relay. With Ex devices this is possible via a built-in optocoupler and a switching amplifier. In this state, the solenoid valve is opened for 7.5 seconds every 4 minutes. A BEKOMAT® filled in a pressureless state is automatically alarm-free again under pressure. The drained condensate is now sent to the ÖWAMAT® oil-water separator for disperse condensate for treatment. In the case of stable emulsions, we recommend the BEKOSPLIT® splitting system for almost waste-free processing. Both systems offer legally compliant process technology for treating your compressed air condensate. Downloads Technical Data BEKOMAT® 6 CO EX , PDF( Size: 702 KB ) Catalog BEKOMAT® 6 CO EX , PDF( Size: 509 KB )

Net €2,105.00 €2,504.95*
BEKOMAT® 8, BEKO condensate drain
BEKO condensate drain BEKOMAT® 8 For applications in large compressors The complete housing of this BEKOMAT® condensate drain is made of cast stainless steel and is therefore designed for use in aggressive atmospheres, as well as for the discharge of condensates from special gas compression. They are mainly utilised in petroleum plants and refineries, in the petrochemical industry and in crude or mineral oil plants. These are the largest electronically level-controlled condensate drain systems available on the market and have been specially designed and built for these requirements. Technical data of BEKOMAT® 8 BEKOMAT® BEKOMAT® 8 Compressor Capacity [m³/min] 9.360 - 14.400 Voltage 230 VAC / 50...60Hz Operating pressure [bar] 0,5 ... 10 Temperature [°C] +1 to + 60 Condensate feed Flansch C50 x 60,3 DIN1092-1 Dimensions B x H [mm] 484 x 485 Application Oil-contaminated condensate / oil-free, often aggressive condensate / aggressive condensate from compressed gas compressors   Downloads Technical Data BEKOMAT® 8 CO EX , PDF( Size: 2.8 MB ) Catalog BEKOMAT® 8 CO EX , PDF( Size: 820 KB )

Net €9,272.00 €11,033.68*
%
OWAMAT® 10 , 2.4m3/min  Oil water separator
Oil water separator OWAMAT® 10 - QWIK-PURE CS200 , 2.4m3/min The clean solution that fits your budget and protects the environment: Condensate processing with OWAMAT ® Legislators demand that discharged condensate is processed safely and properly. BEKO make it easy for operators to meet the legal requirements – with our extensive range of condensate processing solutions that reflect our commitment to sustainability. With our Oil water separator OWAMAT ® oil water separator reaction splitting plants, we offer cost-effective and environmentally friendly solutions for the disposal of dispersed and emulsified condensates. These systems are designed to be environmentally friendly. They are cost-efficient on-site units for the processing of condensate in compliance with all applicable statutory regulations.     Function of OWAMAT® For the processing, the oil-containing condensate first flows under pressure into the pressure relief chamber. Here, the pressure is reduced without causing turbulence in the downstream separating tank for the separation of free oils. Any entrained coarse dirt particles are retained in a removable receiver. In the separating tank, the oil settles on the surface as a result of gravity separation and is led into the spillproof oil receiver.     Technical Data of Oil water separator OWAMAT® 10  Oil water separator OWAMAT OWAMAT® 10  max. compressor performance:  2.4 m3/min  Container volume:  10 l  Capacity:  4.3 l  Pre lter:  2.5 l  Main lter:  2.6 l  Condensate inlet (hose size):  2 x G1⁄2 inside (Ø inside = 10 mm)  Water (hose size):  1 x G1⁄2 inside (Ø inside = 10 mm)  Weight (empty):  3.5 kg  Min./max. temperature  +5 ... +60 °C  Max. operating pressure at inlet  16 bar  Maintenance of ÖWAMAT® Weekly wastewater test – Fill the test glass at the Sampling cock. – Compare the cloudiness with the reference jar If the sample is clearer than the reference cloudiness – the filter is O.K. (Fig. 1) If the sample is cloudier than the reference cloudiness – the filter needs to be changed! (Fig. 2) Never pour any foreign liquid into the pressure relief chamber! This can impair the filter efficiency of the ÖWAMAT®.   Before any maintenance– Shut off condensate inlet (1) if necessary switch off compressor Maintenance– Hoses and hose connections must be inspected regularly (2)  Downloads Technical Data of Oil water separator OWAMAT® 10 , PDF( Size: 747 KB ) Catalog Oil water separator , PDF( Size: 309 KB )

Net €330.65 €393.47* €462.91* (15% saved)
%
OWAMAT® 11 , 4.9m3/min  Oil water separator
Oil water separator OWAMAT® 11 - QWIK-PURE CS200 , 4.9m3/min Safe and efficient condensate separation: OWAMAT®  OWAMAT has been a tried and tested oil-water separation system for dispersed condensates for decades. It has been awarded a building regulation´s approval for the versions with and without free oil separation, for synthetic or mineral oils as well as for processing condensate generated by piston- and screw compressors, therefore not requiring any legislation for water protection approval.   Function of oil water separator OWAMAT® 10,11 The oil-contaminated condensate can be fed under pressure to the OWAMAT® unit (1). The pressure is reduced in the pressure relief chamber (2). The condensate flows steadily into the subjacent filter stage without turbulence and runs through the two-stage OEKOSORB® replacement filter. The OEKOSORB® replacement filter (3) comprises a prefilter and a main filter for binding any residual oil constituents. The water flows out of the OWAMAT® oil-water separator through the water outlet (6) and can be discharged directly into the sewer system. A sampling valve (5) is provided so that the wastewater quality can be checked at any time. 1 Condensate inlet 2 Pressure relief chamber 3 Prefilter/main filter 4 Riser 5 Sampling valve 6 Water outlet   Technical Data of Oil water separator OWAMAT® 11  Oil water separator OWAMAT® OWAMAT® 11  max.compressor performance:  4.9 m3/min  Container volume:  18.6 l  Capacity:  11.7 l  Pre lter:  4.7 l  Main lter:  4.8 l  Condensate inlet (hose size):  2 x G1⁄2 inside (Ø inside = 10 mm)  Water (hose size):  1 x G1⁄2 inside (Ø inside = 10 mm)  Weight (empty):  5.75 kg  Min./max. temperature  +5 ... +60 °C  Max. operating pressure at inlet  16 bar   Downloads Technical Data of Oil water separator OWAMAT® 10,11 , PDF( Size: 747 KB ) Catalog Oil water separator , PDF( Size: 309 KB )

Net €556.75 €662.53* €779.45* (15% saved)
%
QWIK-PURE® 10, Oil water separator
the QWIK-PURE ® opens up new possibilities Classic oil-water separators based on the principle of gravity separation can hardly be improved in terms of process technology. So, as condensate technology experts with decades of experience, we have paid special attention to the people who work with the product. What is important to them, what drives them and how can we give them the highest degree of decision-making reliability and flexibility while integrating the requirements of modern industry? As a result, we present the QWIK-PURE®, the first active oil-water separator with which we have fundamentally redefined condensate treatment and will change it worldwide.   Technical Data QWIK-PURE® 10, Oil water separator Operating mode static* Maximum condensate flow 12 l/h Condensate inlet connection 3 x G1/2", outside | 1 x G1", outside | Hose nozzle Condensate drain connection 1 x 23 mm (0.91 in), outside, Hose nozzle Media Compressor condensate, oily Maximum oil concentration at condensate drain 20mg/l Maximum operating pressure at condensate inlet 16 bar(g) Minimum / maximum operating temperature, Fluids and environment +5 … +50 °C Relative humidity of the environment ≤10 … 80 %, Without condensation Weight 21 Kg Number of replacement cartridges 1 Qwik-Pure is a real innovation among oil-water separators. The highly effective oil-water separation process has been perfected with new technology and innovative concepts.Downloads QWIK-PURE® Catalog, PDF( Size: 3.8 MB ) QWIK-PURE®10 Original installation and operation manual, PDF( Size: 9 MB )

Net €1,223.10 €1,455.49* €1,617.21* (10% saved)
%
QWIK-PURE® 15, Oil water separator
QWIK-PURE ® Ergonomic operation protects operators The absorbed oils are bound in the hermetically sealed cartridges. This reliably protects the operators from contamination and complies with the limit values for the discharged waste water - regardless of the compressor type and the oils used. All versions use the same cartridge with transparent operation. The Qwik-Pure system status is displayed at all times and is clearly visible on the control panel. A green LED bar shows the remaining capacity from 100% to zero. When a cartridge change is required, the display changes from green to red and the guided changing process can be started manually. Therefore, residual condensate is automatically pushed out of the cartridge's pipe system with several small bursts of air. Integrated bottom valves prevent condensate from escaping from the cartridge. The tightly closed cartridge can be easily removed and replaced with a maximum total weight of 25kg. The saturated cartridge is easy and convenient to transport.    Technical Data QWIK-PURE® 15, Oil water separator Operating mode active Maximum condensate flow 19 l/h Condensate inlet connection 3 x G1/2", outside | 1 x G1", outside | Hose nozzle Condensate drain connection 1 x 23 mm (0.91 in), outside, Hose nozzle Media Compressor condensate, oily Maximum oil concentration at condensate drain 20mg/l Maximum operating pressure at condensate inlet 16 bar(g) Minimum / maximum operating temperature, Fluids and environment +5 … +50 °C Relative humidity of the environment ≤10 … 80 %, Without condensation Weight 24 Kg Number of replacement cartridges 1   Technical data of the control unit FRC Minimum / maximum operating pressure, compressed air 3 … 15 bar(g) Cleanliness class, compressed air 2:4:2 Connection, compressed air 8 mm (0.31 in), outside, Hose nozzle Operating voltage 90 … 264 VAC / 24 VDC Frequency range 50 … 60 Hz Power consumption 10 VA Protection class IP54 Downloads QWIK-PURE® Catalog, PDF( Size: 3.8 MB )QWIK-PURE®15-90 Original installation and operation manual, PDF( Size: 16 MB )

Net €1,824.30 €2,170.92* €2,412.13* (10% saved)
%
QWIK-PURE® 30, Oil water separator
QWIK-PURE ® Unique process, functional and future-proof Due to the innovative mode of operation, a maximum of process and functional reliability is achieved. The integrated control system permanently displays the remaining capacity and thus ensures transparency and plannability. It also guides you through the quick and easy cartridge change and helps with service tasks via a local WLAN network. And if the power should fail, the fail-safe function ensures safe operation. In this case, the QWIK-PURE® behaves like a conventional gravity separator. Qwik-Pure stands for optimal operational safety for conventional oil-water separators. This is ensured by the unique and intelligent operating principle and reliable monitoring by the device's electronic unit.     Technical Data QWIK-PURE® 30, Oil water separator Operating mode active Maximum condensate flow 38 l/h Condensate inlet connection 3 x G1/2", outside | 1 x G1", outside | Hose nozzle Condensate drain connection 1 x 23 mm (0.91 in), outside, Hose nozzle Media Compressor condensate, oily Maximum oil concentration at condensate drain 20mg/l Maximum operating pressure at condensate inlet 16 bar(g) Minimum / maximum operating temperature, Fluids and environment +5 … +50 °C Relative humidity of the environment ≤10 … 80 %, Without condensation Weight 31 Kg Number of replacement cartridges 2   Technical data of the control unit FRC Minimum / maximum operating pressure, compressed air 3 … 15 bar(g) Cleanliness class, compressed air 2:4:2 Connection, compressed air 8 mm (0.31 in), outside, Hose nozzle Operating voltage 90 … 264 VAC / 24 VDC Frequency range 50 … 60 Hz Power consumption 10 VA Protection class IP54 Downloads QWIK-PURE® Catalog, PDF( Size: 3.8 MB )QWIK-PURE®15-90 Original installation and operation manual, PDF( Size: 16 MB )

Net €2,248.20 €2,675.36* €2,972.62* (10% saved)
%
QWIK-PURE® 60, Oil water separator
QWIK-PURE ® Extremely flexible and future-proof The integrated Modbus interface enables integration into higher-level monitoring and control systems and provides additional future-proofing thanks to its IIOT capability. A modular concept allows the number of cartridges to be flexibly adjusted to individual requirements, with up to 6 cartridges per system. This ensures optimal condensate treatment for all applications, with a quick change time of under 10 minutes, supported by the optimized guided service flow for clean cartridge changes. Technical Data QWIK-PURE® 60, Oil water separator Operating mode active Maximum condensate flow 76 l/h Condensate inlet connection 3 x G1/2", outside | 1 x G1", outside | Hose nozzle Condensate drain connection 1 x 23 mm (0.91 in), outside, Hose nozzle Media Compressor condensate, oily Maximum oil concentration at condensate drain 20mg/l Maximum operating pressure at condensate inlet 16 bar(g) Minimum / maximum operating temperature, Fluids and environment +5 … +50 °C Relative humidity of the environment ≤10 … 80 %, Without condensation Weight 45 Kg Number of replacement cartridges 4   Technical data of the control unit FRC Minimum / maximum operating pressure, compressed air 3 … 15 bar(g) Cleanliness class, compressed air 2:4:2 Connection, compressed air 8 mm (0.31 in), outside, Hose nozzle Operating voltage 90 … 264 VAC / 24 VDC Frequency range 50 … 60 Hz Power consumption 10 VA Protection class IP54 Downloads QWIK-PURE® Catalog, PDF( Size: 3.8 MB )QWIK-PURE®15-90 Original installation and operation manual, PDF( Size: 16 MB )

Net €2,812.50 €3,346.88* €3,718.75* (10% saved)
QWIK-PURE® 90, Oil water separator
QWIK-PURE® simply grows with you Each QWIK-PURE® model can be easily expanded or scaled down according to current needs. This creates decision-making reliability and additional safety. And because exactly the same cartridge is used in all models, procurement and stock-keeping become even easier. Qwik-Pure represents a radical rethinking of oil-water separation, offering safe, compatible, certified, ergonomic, fast, modular, clean and universal functions. It meets all hygienic, efficient, clean, safe and modular requirements, making it the main feature of the new Qwik-Pure generation. Technical Data QWIK-PURE® 90, Oil water separator Operating mode active Maximum condensate flow 114 l/h Condensate inlet connection 3 x G1/2", outside | 1 x G1", outside | Hose nozzle Condensate drain connection 1 x 23 mm (0.91 in), outside, Hose nozzle Media Compressor condensate, oily Maximum oil concentration at condensate drain 20mg/l Maximum operating pressure at condensate inlet 16 bar(g) Minimum / maximum operating temperature, Fluids and environment +5 … +50 °C Relative humidity of the environment ≤10 … 80 %, Without condensation Weight 60 Kg Number of replacement cartridges 6   Technical data of the control unit FRC Minimum / maximum operating pressure, compressed air 3 … 15 bar(g) Cleanliness class, compressed air 2:4:2 Connection, compressed air 8 mm (0.31 in), outside, Hose nozzle Operating voltage 90 … 264 VAC / 24 VDC Frequency range 50 … 60 Hz Power consumption 10 VA Protection class IP54 Downloads QWIK-PURE® Catalog, PDF( Size: 3.8 MB )QWIK-PURE®15-90 Original installation and operation manual, PDF( Size: 16 MB )

Net €4,117.00 €4,899.23*
Service unit for BEKOMAT® 20 and BEKOMAT® 20FM
Service unit for BEKOMAT® 20 and BEKOMAT® 20FM Service unit BEKOMAT® Details information For BEKOMAT® 20 Price (€) 20 FM Price (€) Wearing part set 4003701 (XEKA20101) 59 4003701 (XEKA20101) 59 Diaphragms 3 pcs 2000496 (XEKA10106) 75 2000496 (XEKA10106) 75 Diaphragms 3 pcs 4003700 (XEKA20103) 43 4003700 (XEKA20103) 43 Top cover 4003703 (XEKA20010) 64 4003704 (XEKA20012) 66 Sensor control board - - 4003705 (XEKA20201) 204 Sensor PCB 230 VAC 4003706 (XEKA20114) 129 2001501 (XEKA21214) 80 Sensor PCB 200 VAC 4004089 (XEKA20119) 129 4001278 (XEKA21219) 80 Sensor PCB 115 VAC 4003707 (XEKA20115) 129 2001502 80 Sensor PCB 100 VAC 4003708 130 4001276 (XEKA21218) 80 Sensor PCB 24 VAC 4003709 129 2001504 (XEKA21216) 80 Sensor PCB 24 VDC - - 2001915 (XEKA21217) 80 Downloads Technical Data BEKOMAT® 20, 20FM, PDF (Size: 2.5 MB) Catalog BEKOMAT® 20, 20FM, PDF ( Size: 330 KB )

From Net €43.00 €51.17*
Service unit for BEKOMAT® 21 and BEKOMAT® 21 PRO
Service unit BEKOMAT® Details information For BEKOMAT® 21 Preis (€) 21 PRO Preis (€) Wearing part set 2001365 (XEKA21101) 59 2001365 (XEKA21101) 59 Diaphragms 3 pcs 2000496 (XEKA10106) 75 2000496 (XEKA10106) 75 Diaphragm seat 2001367 (XEKA21103) 43 2001367 (XEKA21103) 43 Sealing kit 2001366 (XEKA21102) 30 2001366 (XEKA21102) 30 Top cover 2001913 (XEKA21010) 66 2001914 (XEKA21011) 66 Sensor control board - - 2001494 (XEKA21203) (4047963) 137 Sensor PCB 230 VAC 2001488 (XEKA21114) 130 2001495 (XEKA21204) 80 Sensor PCB 200 VAC 4004090 130 4001277 (XEKA21209) 80 Sensor PCB 115 VAC 2001489 130 2001496 80 Sensor PCB 100 VAC 4001273 (XEKA21116) 130 4001275 (XEKA21208) 80 Sensor PCB 24 VAC 2001490 (XEKA21117) 129 2001497 (XEKA21206) 80 Sensor PCB 24 VDC - - 2001498 (XEKA21207) 80

From Net €30.00 €35.70*
Service unit for BEKOMAT® 12, 12 CO, 12 CO PN 63, 12 CO NI, 12 KW
Service unit BEKOMAT® Details information For BEKOMAT® 12 Preis (€) 12 CO Preis (€) 12 CO PN 63 Preis (€) 12 CO NI Preis (€) 12 KW Preis (€) Wearing part set 2000049 (XEKA12101) 82 2000049 (XEKA12101) 82 2000748 (XEKA12301) 93 - - - - Diaphragms 3 pcs 4003555 (XEKA00027) (4045068) 109 4003555 (XEKA00027) (4045068) 109 2000437 149 - - - - Diaphragm seat 2800829 (XEKA11011) 43 2800829 (XEKA11011) 43 - - - - - - Valve 4027846 103 4027847 121 4027848 482 - - - - Valve attachment components 2000052 (XEKA12102) 38 2000053 (XEKA12202) 41 2000054 (XEKA12302) 393 - - - - Sealing kit 2000058 (XEKA12104) 26 2000058 (XEKA12104) 26 2000749 (XEKA12304) 28 2000058 (XEKA12104) 26 2000058 (XEKA12104) 26 Housing 2000060 (XEKA12105) 83 2000061 (XEKA12205) 132 2000234 (XEKA12305) 134 - - 2000192 (XEKA12106) 115 Top cover 2000066 (XEKA12005) 82 2000066 (XEKA12005) 82 2000066 (XEKA12005) 82 2000066 (XEKA12005) 82 2000194 (XEKA12007) 85 Sensor control board 2000062 (XEKA12001) (4047971) 211 2000062 (XEKA12001) (4047971) 211 2000062 (XEKA12001) (4047971) 211 - - 2000193 (XEKA12006) 211 Sensor PCB 230 VAC 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 Sensor PCB 200 VAC 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 Sensor PCB 115 VAC 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 Sensor PCB 100 VAC 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 Sensor PCB 24 VAC 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 Sensor PCB 24 VDC 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 Downloads Technical Data BEKOMAT® 12 , PDF( Size: 1.2 MB ) Catalog BEKOMAT® 12 , PDF( Size: 430 KB )

From Net €26.00 €30.94*
Service unit for BEKOMAT® 13, 13 CO, 13 CO PN 25 | 40 | 50
Service unit BEKOMAT® Details information For BEKOMAT® 13 Preis (€) 13 CO Preis (€) 13 CO PN 25 | 40 | 50 Preis (€) Wearing part set 2000067 (XEKA13101) 85 2000067 (XEKA13101) 85 2000366 (XEKA13301) 102 Diaphragms 3 pcs 4002451 (XEKA00020) (4053197) 148 4002451 (XEKA00020) (4053197) 148 2000439 (XEKA00019) 160 Diaphragm seat 2001118 (XEKA13109) 43 2001118 (XEKA13109) 43 2000351 151 Valve 4027849 131 4027850 149 4027851 547 Valve attachment components 2000071 (XEKA13102) 52 2000072 (XEKA13202) 55 2000371 (XEKA13302) 456 Sealing kit 2000073 (XEKA13104) 30 2000073 (XEKA13104) 30 2000367 (XEKA13304) 33 Housing 2000075 (XEKA13105) 196 2000076 (XEKA13205) 367 2000368 (XEKA13305) 491 Housing cover 2000077 (XEKA13106) 91 2000078 (XEKA13206) 296 2000369 (XEKA13306) 343 Top cover 2000066 (XEKA12005) 82 2000066 (XEKA12005) 82 2000066 (XEKA12005) 82 Sensor control board 2000079 (XEKA13001) (4047967) 211 2000079 (XEKA13001) (4047967) 211 2000079 (XEKA13001) (4047967) 211 Sensor PCB 230 VAC 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 Sensor PCB 200 VAC 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 Sensor PCB 115 VAC 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 Sensor PCB 100 VAC 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 Sensor PCB 24 VAC 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 Sensor PCB 24 VDC 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 Downloads Technical Data BEKOMAT 13® , PDF( Size: 1.5 MB ) Catalog BEKOMAT® 13 , PDF( Size: 430 KB )

From Net €30.00 €35.70*
Service unit for BEKOMAT® 14, 14 CO, 14 CO PN 25
Service unit BEKOMAT® Details information For BEKOMAT® 14 Preis (€) 14 CO Preis (€) 14 CO PN 25 Preis (€) Wearing part set 2000731 (XEKA14101) 85 2000731 (XEKA14101) 85 2002556 (XEKA14301) 106 Diaphragms 3 pcs 4002451 (XEKA00020) 148 4002451 (XEKA00020) 148 2000439 (XEKA00019) 160 Diaphragm seat 2001118 (XEKA13109) 43 2001118 (XEKA13109) 43 2000351 151 Valve 4027849 131 4027850 149 4027851 547 Valve attachment components 2000071 (XEKA13102) 52 2000072 (XEKA13202) 55 2000371 (XEKA13302) 456 Sealing kit 2000080 (XEKA14104) 30 2000080 (XEKA14104) 30 4000923 33 Housing 2000082 (XEKA14105) 240 2000083 (XEKA14205) 446 2000083 (XEKA14205) 446 Housing cover 2000084 (XEKA14106) 146 2000085 (XEKA14206) 319 2000085 (XEKA14206) 319 Top cover 2000066 (XEKA12005) 82 2000066 (XEKA12005) 82 2000066 (XEKA12005) 82 Sensor control board 2000086 (XEKA14001) (4047968) 217 2000086 (XEKA14001) (4047968) 217 2000086 (XEKA14001) (4047968) 217 Sensor PCB 230 VAC 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 2000063 (XEKA12002) 103 Sensor PCB 200 VAC 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 2000349 (XEKA12008) 103 Sensor PCB 115 VAC 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 2000064 (XEKA12003) 103 Sensor PCB 100 VAC 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 2000611 (XEKA12010) 103 Sensor PCB 24 VAC 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 2000065 (XEKA12004) 103 Sensor PCB 24 VDC 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 2000756 (XEKA12012) 103 Downloads Technical Data BEKOMAT® 14 , PDF( Size: 1.5 MB ) Catalog BEKOMAT® 14 , PDF( Size: 430 KB )

From Net €30.00 €35.70*
Service unit for BEKOMAT® 16 CO
Service unit BEKOMAT® Details information For BEKOMAT® 16 CO Preis (€) Wearing part set 2000087 (XEKA16201) 106 Diaphragms 3 pcs 4002451 (XEKA00020) (4053197) 148 Diaphragm seat - - Valve 2000089 (XEKA16203) 175 Valve attachment components 2000088 (XEKA16202) 43 Sealing kit 2000090 (XEKA16204) 33 Housing 2000092 (XEKA16206) 961 Housing cover 2000091 (XEKA16205) 394 Top cover 2000066 (XEKA12005) 82 Sensor control board 2000093 (XEKA16001) (4047969) 217 Sensor PCB 230 VAC 2000063 (XEKA12002) 103 Sensor PCB 200 VAC 2000349 (XEKA12008) 103 Sensor PCB 115 VAC 2000064 (XEKA12003) 103 Sensor PCB 100 VAC 2000611 (XEKA12010) 103 Sensor PCB 24 VAC 2000065 (XEKA12004) 103 Sensor PCB 24 VDC 2000756 (XEKA12012) 103 Downloads Technical Data BEKOMAT® 16 CO , PDF( Size: 1.2 MB ) Catalog BEKOMAT® 16 CO , PDF( Size: 430 KB )

From Net €33.00 €39.27*
Service unit for BEKOMAT® 31U , 32U , 33U , 33U CO
Service unit BEKOMAT® Details information For BEKOMAT® 31U Preis (€) 32U Preis (€) 33U Preis (€) 33U CO Preis (€) Connection adapter 4010155 (XEKA31001) 44 4010155 (XEKA31001) 44 - - - - Sealing kit 4024386 18 4024392 18 4024397 18 4024397 18 Designshell 4010164 (XEKA31011) 20 4010167 (XEKA32011) 26 4010167 (XEKA32011) 26 4010167 (XEKA32011) 26 Service Unit 4023607 (XEKA31101) 129 4023571 139 4023633 (XEKA33101) 180 4023635 (XEKA33103) 212 Downloads Technical Data BEKOMAT® 31U , PDF( Size: 761 KB ) Service Unit BEKOMAT® 31U , PDF( Size: 480 KB ) Technical Data BEKOMAT® 32U , PDF( Size: 777 KB ) Service Unit BEKOMAT® 32U , PDF( Size: 413 KB ) Technical Data BEKOMAT® 33U , PDF( Size: 1 MB ) Service Unit BEKOMAT® 33U , PDF( Size: 553 KB ) Catalog BEKOMAT® 31U, 32U, 33 U, PDF( Size: 368 KB )

From Net €18.00 €21.42*
Service unit for BEKOMAT® 3, 3 CO, 3 E, 3 E 25, 3 E 63
Service unit BEKOMAT® Details information For BEKOMAT® 3 Preis (€) 3 CO Preis (€) 3 E Preis (€) 3 E 25 Preis (€) 3 E 63 Preis (€) Wearing part set 2800656 (XEKA03001) 88 2800670 (XEKA03015) 88 2800702 (XEKA03047) 125 2800702 (XEKA03047) 125 2800702 (XEKA03047) 125 Diaphragms 3 pcs 4002451 (XEKA00020)(4053197)148 4002451 (XEKA00020) (4053197) 148 4002451 (XEKA00020) (4053197) 148 2000439 160 2000439 160 Sealing kit 2800658 (XEKA03003) 26 2800671 (XEKA03016) 26 2800689 (XEKA03034) 50 2800703 (XEKA03048) 50 2800703 (XEKA03048) 50 Top cover 2800661 (XEKA03006) 90 2800661 (XEKA03006) 90 2800690 (XEKA03035) 90 2800690 (XEKA03035) 90 2800690 (XEKA03035) 90 Service air valve 2800663 (XEKA03008) 91 2800717 (XEKA03062) 110 2800663 91 2800717 (XEKA03062) 110 2800717 (XEKA03062) 110 Control air cap 2800665 (XEKA03010) 34 - - - - - - - - Valve 2800664 (XEKA03009) 214 2800673 (XEKA03018) 335 2800693 (XEKA03038) 429 2800705 (XEKA03050) 446 2800718 (XEKA03063) 355 Upper housing 2800667 (XEKA03012) 321 2800674 (XEKA03019) 423 2800696 (XEKA03041) 2452 2800696 (XEKA03041) 2452 2800719 (XEKA03064) 2469 Bottom housing 2800668 (XEKA03013) 139 2800675 (XEKA03020) 234 2800720 (XEKA03065) 1578 2800720 (XEKA03065) 1578 2800720 (XEKA03065) 1578 Sensor board 230 VAC 2800659 (XEKA03004) 341 2800659 (XEKA03004) 341 2800659 (XEKA03004) 341 2800659 (XEKA03004) 341 2800659 (XEKA03004) 341 Sensor board 100 VAC 2002200 (XEKA03190) 341 2002200 (XEKA03190) 341 2002200 (XEKA03190) 341 2002200 (XEKA03190) 341 2002200 (XEKA03190) 341 Sensor board 110 VAC 2800698 (XEKA03043) 341 2800698 (XEKA03043) 341 2800698 (XEKA03043) 341 2800698 (XEKA03043) 341 2800698 (XEKA03043) 341 Sensor board 24 VAC 2800699 (XEKA03044) 341 2800699 (XEKA03044) 341 2800699 (XEKA03044) 341 2800699 (XEKA03044) 341 2800699 (XEKA03044) 341 Sensor board 24 VDC - - - - - - - - - -

From Net €26.00 €30.94*
Service unit for BEKOMAT® 6 CO, 6 E 25
Service unit BEKOMAT® Details information For BEKOMAT® 6 CO Preis (€) 6 E 25 Preis (€) Wearing part set 2800670 (XEKA03015) 88 2800702 (XEKA03047) 125 Diaphragms 3 pcs 4002451 (XEKA00020) (4053197) 148 2000439 160 Sealing kit 2800658 (XEKA03003) 26 2800703 (XEKA03048) 50 Top cover 2800661 (XEKA03006) 90 2800690 (XEKA03035) 90 Service air valve 2800663 (XEKA03008) 91 2800717 (XEKA03062) 110 Control air cap 2800665 (XEKA03010) 34 - - Valve 2800664 (XEKA03009) 214 2800705 (XEKA03050) 446 Upper housing 2800789 (XEKA06001) 423 - - Bottom housing 2800790 (XEKA06002) 975 - - Sensor board 230 VAC 2800796 (XEKA06008) 341 2800796 (XEKA06008) 341 Sensor board 100 VAC - - - - Sensor board 110 VAC 2800804 (XEKA06016) 341 2800804 (XEKA06016) 341 Sensor board 24 VAC 4010781 (XEKA06017) 342 4010781 (XEKA06017) 342 Sensor board 24 VDC 2800806 (XEKA06018) 341 2800806 (XEKA06018) 341

From Net €26.00 €30.94*
Replacement filter sets for ÖWAMAT ® 1-2-3-4-5-5R-6-8-20
Replacement filter sets for ÖWAMAT ® 1-2-3-4-5-5R-6-8-20 OEKOSORB ®: Replacement filter sets for ÖWAMAT ® 1-2-3-4-5-5R-6-8-20 Original OEKOSORB® replacement filters Original filters guarantee high performance, operational safety and compliance with water protection legislation. OEKOSORB® filter kit Like all high-performance units, the ÖWAMAT® needs to be serviced. Our filter kits make this an easy task. If you require assistance, contact our service technicians, who are also qualified to examine and assess your entire compressed air system for further optimisation. for ÖWAMAT ® 1/2 3 4 5 5R 6 8 20 Prefilter (l) 1 x 2 – 1 x 4,5 – 1 x 9 1 x 9 1 x 30 – Main filter (l) 1 x 3 1 x 15 1 x 8 2 x 18 1 x 17 2 x 17 2 x 45 1 x 82 Weight (kg) 1 2,5 3 7,5 4,5 9 25 23 Order No. 4027544 (XVKT02AF1) 4027548 (XVKT03AF1) 4027550 (XVKT04AF1) 4027554 (XVKT05AF2) 4027556 (XVKT5RAF1) 4027557 (XVKT06AF2) 4027562 (XVKT08AF2) 4027546 (XVKT20AF1) Price (€) 101 150 178 322 224 375 927 675   Downloads Catalog OEKOSORB®, PDF (Size: 75 KB) Catalog Oil water separator , PDF( Size: 309 KB )

From Net €101.00 €120.19*
Replacement filter sets for ÖWAMAT ® 10-11-12-14-15-16
OEKOSORB ®: Replacement filter sets for ÖWAMAT ® 10-11-12-14-15-16 Extended warranty The oil-water separator, high-performance quality product comes with a 2-year warranty. To ensure trouble-free and efficient operation use only original components. Operation with third-party components or consumables shall void the warranty.   for ÖWAMAT ® 10 11 12 14 15 16 Prefilter (l) 1 x 2,5 1 x 4,7 1 x 2,5 1 x 6,7 1 x 18,5 1 x 37,2 Main filter (l) 1 x 2,6 1 x 4,8 1 x 5,9 1 x 11 1 x 20,4 1 x 40,3 Weight (kg) 0,5 1,98 1,98 3,38 6,03 11,12 Order No. 4010719 (XVKT10BF1) 4011999 (XVKT11BF1) 4010711 (XVKT12CF1) 4010712 (XVKT14CF1) 4010713 (XVKT15CF1) 4010714 (XVKT16CF1) Price (€) 105 140 171 237 384 648   Downloads Catalog OEKOSORB®, PDF (Size: 75 KB) Catalog Oil water separator , PDF( Size: 309 KB )

From Net €105.00 €124.95*
Replacement cartridge QWIK-PURE®
One cartridge fits all QWIK-PURE® models This facilitates procurement, stock-keeping and avoids wrong orders.  Ergonomically designed When developing the cartridges, we primarily thought about the users: The inlet tube was designed as a handy and stable handle so that the cartridge can be easily transported and mounted. Thanks to the controlled drainage, even a fully saturated cartridge weighs less than 25 kg. Clean cartridge change A reliable closing valve is integrated in the base so that nothing drips onto the floor after changing the cartridge. The blind plugs supplied for the upper openings ensure that no liquids can escape there either. Consistently hygienic Due to the hermetically sealed design, neither users nor service personnel come into contact with the absorbed substances inside. Everything that has been bound in the pre-filter and main filter reliably remains here and does not contaminate people in the vicinity or the discharged processed condensate.Downloads QWIK-PURE® Catalog, PDF( Size: 3.8 MB )

Net €251.00 €298.69*
Upgrade kits QWIK-PURE® 60 to 90
QWIK-PURE ® 30 to 60 or 60 to 90 This supplementary unit is simply plugged in at the side. The extended capacity is entered in the control unit and the additional power is available. In addition to the base plate, 4 or 6 new cartridges are included in this package. When attached, the new capacity is 60 m³/min or 90 m³/min. Downloads QWIK-PURE® Catalog, PDF( Size: 3.8 MB )

Net €1,986.00 €2,363.34*
If we want to have good result in air compressor we should have high quality compressed air treatment tools.
Beko technologies offers us the high quality equipment in compressed air treatment system.


What is compressed air treatment and why do you need it?
At first compressed air treatment allow your compressed air system to run more efficiently. Because with that you can have the clean air in compressed air system line. It can also run faster and doesn’t contain any particles that can corrode the machines,
There are many ways and equipment that clean and filtering the compressed air. Each part of an air treatment system does an important responsibility but all the tools have unique aim that is the cleanest air compressor.
Bekomat is one part of this line that beko technologies company supplies. Compressed air filters are used for high efficient removal of solid particles, water, oil aerosols, hydrocarbons, odour and vapours from compressed air systems.

Function of BEKOMAT 

The  BEKOMAT  drains off condensate without loss of compressed air, thus reducing energy costs and CO2 emissions. This is made possible by the integrated capacitive sensor, smart electronics for volume-controlled condensate discharge and a proven pilotcontrolled solenoid valve with a special discharge diaphragm.

Advantages of BEKOMAT® with service concept

Plug & Play

  •  No weekly inspections, sieve inspections or cleaning required

Service-Unit

  • Pressure and function tested with two-year warranty
  • Power and alarm signalling as standard
  • For operation at temperatures up to +70°C

Ease of installation and maintenance-free

  • Versatile connection options
  • Easy exchange of service unit, even in confined spaces
  • No installation work during maintenance

Fully automatic operation and monitoring

  • Connection for modern system monitoring
  • In case of increased contamination, a self-cleaning process starts automatically
  • Service indicator for punctual exchange of the service unit